Home Up R & D History of CA

 

PRODUCT SPECIFICATION

TUFFBOND for Wood Serious

(Thin, Medium, Thick)

Cyanoacrylate Adhesive

DESCRIPTION

 

TUFFBOND for Wood Serious is a high strength, top fast setting adhesive which can be used for virtually any type of fastening job. It has been specially formulated to achieve the strongest possible bond between well-mated, non-porous surfaces; is specially designed for bonding and repairing of wooden furniture. Better efficiency and quality combined with cost saving have made TUFFBOND for Wood Serious ato  be a  substitute for repairing of wooden material. TUFFBOND for Wood Serious is a one-component, solvent-free system and does not require the use of a catalyst, heat or clamps. When a thin layer of TUFFBOND for Wood Serious applied between two surfaces comes into contact with atmospheric moisture, a rapid polymerization occurs producing the ultimate bond.

 

PHYSICAL PROPERTIES

 

Liquid State

Cured State

Base                       Ethyl Cyanoacrylate

Color                                      Clear

Color                               clear

Specific Gravity(20oC)                 1.1~1.3

Specific Gravity(20oC)           1.053~1.060

Softening Point( o C)            145 (1 76 O  F )

Refractive Index ( n )                1.439

Refractive Index( n )                   1.490

Flash Point (oC)                   80(176oF)

Dielectric Constant(at 10MHz)              3.5

Shelf Life                       4-6 Months

Dielectric Loss(at 10MHz)                0.067

Boiling Point(o C)                65/6mm Hg

Soluble in Acetone, Dimethyl formamide, romethame, Dimethyl sulfoxide

Viscosity(cps)…………….……

TUFFBOND for Wood (Thin)……….……3-5

TUFFBOND for Wood (Medium).80-120

TUFFBOND for Wood (Thick)….……700-1000

 

DIRECTIONS  FOR  USE

 

1.            Make sure the surfaces to be bonded are clean and dry(preferable to solvent-wipe plastics , glass, and rubber, and to acid-treat metals).      

2.            Dispense a drop or drops to one surface only. Apply only enough to leave a thin film after compression.

3.            Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bond develops in less than one minute. (Maximum strength is achieved in 24 to 48 hours).

4.       Wipe off excess adhesive from the top of the container and recap TUFFBOND for Wood Serious if left uncapped, may deteriorate by contamination from moisture in the air.

5.        Because TUFFBOND for Wood Serious condenses by polymerization, sometimes a whitening will occur on the surface of the container or the bonded materials. Should this happen, wipe surfaces well with acetone.

BOND STRENGTH

(TENSILE SHEAR STRENGTH, CURED FOR 24 HOURS AT 20-25℃(68-77℉))

                                        KG/CM2

KG/CM2

Rigid PVC to Rigid PVC

△50-70

SBR to SBR

△5-10

ABS to ABS

△50-70

Steel to Steel

200-220

Polycarbonate to Polycarbonate

△70-120

Stainless steel to Stainless steel

200-220

Polystyrene to Polystyrene

△40-45

Aluminum to Aluminum

170-190

Natural rubber to Natural rubber

△5-10

Copper to Copper

150-170

*Neoprene to Neoprene

△5-10

Steel to Rigid PVC

△40-60

NBR to NBR……

△5-10

Stainless steel to Neoprene

△5-10

ABS to SBR…………….

△5-10

 

 

 

CURE SPEED

 

TUFFBOND for Wood (Thin)  Seconds

Seconds

ABS to ABS

5-15

NBR to NBR

3-5

Wood to Wood

>60

Stainless steel to Stainless steel

35-45

ABS to Stainless steel

30-40

ABS to NBR

3-5

NBR to Stainless steel

50-60

Wood to ABS

20-30

TUFFBOND for Wood (Medium)Seconds

Seconds

ABS to ABS

15-20

NBR to NBR

3-5

Wood to Wood

>60

Stainless steel to Stainless steel

50-60

ABS to Stainless steel

40-50

ABS to NBR

5-10

NBR to Stainless steel

>60

Wood to ABS

25-35

TUFFBOND for Wood (Thick)  Seconds

Seconds

ABS to ABS

20-25

NBR to NBR

3-5

Wood to Wood

>60

Stainless steel to Stainless steel

50-60

ABS to Stainless steel

40-50

ABS to NBR

5-10

NBR to Stainless steel

>60

Wood to ABS

30-40

 

PRECAUTION

 

1.            Use with proper ventilation. Avoid contact with skin and eyes.

2.            If contact with skin occurs, rinse with warm water or dissolve gradually with solvent such as acetone, dimethylformanide, or nitromethane. Do not try to remove forcibly.

3.            If adhesive gets into eye, keep eye open and rinse thoroughly. Seek medical attention immediately.

4.            Keep well out of reach of children.

5.          Keep adhesive in a cool, dry place 20-25℃(68-77oF). For long term storage, refrigeration (5oC or 40oF) is recommended.